EMS-Trade
Cooling
Loop consumables

Document ECT-01 · REV C · ISSUED 2026-09 Six lines · 48 sheets

Plate 25 · Filter cartridges · line 03 of six

Pick the grade you can live with at the change point

Eight absolute grades, three lengths, and the trade-off that is actually being made when one is chosen.

Request the specification file One business day, with the file attached
A pleated cartridge part way into its housing on a bench, the end cap above the rim and the seal ring laid flat on the bench in front of the body
PL 01

One element, one grade, one length. Everything below is about choosing between them.

01

The selection table, ordered by what it costs you

Section 01 · selection

This table is not ordered by how many parameters a cartridge has. It is ordered by what each choice costs once the loop is running: pressure drop you pay every hour, media surface you pay for once, and the time a change takes you off the branch.

Finer media, longer element, more surface. The three move together, and the loop sets the limit.

Selection by decision · what each choice costs
Decision Options You pay Check against
Grade 1 µm Pressure drop, rising as the pleats load 0.5–0.7 bar
Grade, finer 0.05–0.45 µm Surface area, and an earlier change on the same dirt load branch flow
Grade, coarser 5–100 µm Longer service, and wear particles that stay in the loop ISO 4406
Length 40 in Height in the plant room, and a heavier lift at the change housing
Length, short 10 in Two changes where one would have done low flow branch
Media pleated, bonded end caps Nothing on the loop side, once the seal ring is right seal seat

Read down the third column. A grade that looks better in the first two columns is paid for in the third.

Two cartridge sections side by side on a bench, one with a tight pleat pitch and one with a wide pitch, the media weight visibly different between them
FIG 01

Grade first: the same body, two media, two service lives.

A 40 in element and a 10 in element laid end to end on a bench, the length difference running the full width of the frame
FIG 02

Length second: it changes the change, not the filtration.

A cartridge end cap in close view with the elastomer seal ring lifted just clear of its groove, the machined land behind it bare metal
FIG 03

Media last, and the seal before it: the ring is what makes the grade true.

02

The lengths, photographed against the same bench

Section 02 · lengths

A 10 in cartridge standing on a bench beside a steel rule laid flat, the element shorter than the rule and the end cap level with its base
FIG 04

10 in. One branch, one small flow, a change that takes minutes.

A 20 in cartridge standing on the same bench beside the same steel rule, the rule running past the top of the element
FIG 05

20 in. The length most loop branches are drawn with.

A 40 in cartridge lying on the bench with its length running out of frame, the end cap at the near end and the steel rule laid along its side
FIG 06

40 in. The same seat, twice the media, and a two-person lift.

All three lengths stood together on one bench in the order 10 in, 20 in, 40 in, each with its seal ring laid flat in front of it
FIG 07

Same seat, same seal, three heights. The housing decides which one fits.

03

The boundary figures, and what happens past them

Section 03 · boundaries

Change point
0.5–0.7 bar across the element. Past it, the media is loaded, not working
Cleanliness target
ISO 4406 17/15/12 at the point the loop is signed over
Grade below the target
the element holds the loop at or better than its own rating, and blocks faster
Grade above the target
the loop never reaches the target, whatever the element is rated at
Seal surface
one land, one ring; a nicked land bypasses the media entirely
A loaded element lifted out of its housing, the pleats bowed inward and the surface dark with a layer of captured material, a drip still hanging from the base
FIG 08

Loaded, not bypassed yet. The pleats have closed on themselves.

The seal land on a housing rim in close view, a clean ring-shaped witness mark on the machined face and one small bright nick at the outer edge
FIG 09

A witness mark where the ring sat, and the nick that ends the grade on the label.

04

Four ways a cartridge is misused, and what each one costs

Section 04 · misuse

Run to bypass
the element loads until the seal lifts, and the dirt it held goes downstream in one pass
Wash and refit
rinsing a pleat pack moves the debris deeper into the media and returns it to service
Finer grade, same body
a 0.45 µm element on a branch sized for 1 µm blocks in weeks, and the loop runs on a bypass
Ring reused
an elastomer ring taken off once and refitted seats on the old witness mark and weeps at pressure

The spare ring is in the same bag as the body so this list stays avoidable.

A used element being rinsed over a bucket with a hose, dark water running out of the pleats and collecting in the bucket below
FIG 10

Rinsed and refitted. The water leaving it is the loop's material going back in.

A used seal ring lying beside a new one on a bench, the used ring flattened on its seating face and the new one standing round in its bag
FIG 11

The ring on the left has seated once. That is the whole story of the fourth row above.

05

What travels with a carton of elements

Section 05 · documents and packing

Packed as
carton, elements sealed in their own wrap
Carton quantity
per 10 pcs on 20 in and 40 in, mixed lengths not combined
Rate cards
0.05–100 µm grade ladder printed on the carton and on the spec sheet
Sample
7–10 days with the first article inspection record
Production
25–35 days; the documents listed below travel with the batch
An open carton of cartridges on a bench, elements standing upright in rows with their wrap intact and a packing list resting on the folded lid
FIG 12

The carton as it is closed, with the list that goes with it on top.

A specification sheet for the cartridge range on a bench beside a batch of elements, the sheet folded so that only its ruled table and margin are showing
PL 02

The sheet the request form returns: grade ladder, lengths, media, seal, test record.

Read next · Coolant filtration · Filter housings · Design guides

Document request

Four documents are held for this sheet. Tick the ones you need.

Tick a document, name the grade and the length, and the file comes back attached.

The only promise on this page

One business day, with the file attached.

No other commitment is made on this sheet. Price, stock and lead time are not promised here.

If the form cannot send, the address below takes it instead: sales@ems-cool.com. A request is never accepted and then dropped.
A batch card lying on a stack of sealed cartridges, its ruled columns printed and unfilled, and the carton behind it still open
FIG 13

One batch, one ticket: grade, length, media and the ring that goes with them.

An element standing under an inspection lamp on a bench, the pleat pack straight, the end cap in the light and a magnifier resting beside it
FIG 14

Turned under the lamp before sealing. What the ticket records is what was seen here.